BYD M6
Forged wheel sizing, stance, brake-clearance planning, 5x120 PCD references, 64.1 center-bore references, customer photo cases, and street-ready engineering checks for BYD M6 owners. For Singapore owners comparing BYD wheels and BYD rims, see LFI's BYD wheels Singapore landing page for model-level upgrade guidance.
This guide helps BYD M6 owners choose forged wheels with the right stance, tire support, brake clearance, and road manners. The goal is simple: a wheel that looks right, fits properly, and feels sharp on the actual car.
Width, offset, and concavity specified to the vehicle, not pulled from a generic size chart.
Spoke profile, barrel shape, and backpad are reviewed around the exact brake package.
Lower unsprung mass can sharpen steering, braking feel, and ride control.
| Area | Guide value | Fitment note |
|---|---|---|
| PCD | 5x120 | Confirm exact vehicle before machining. |
| Center bore | 64.1 | Machine hub-centric to the confirmed car. |
| Wheel sizes | 18x8 ET42 | Review tire, brake, fender and ride height together. |
| Wheel models | REX-08 | Face profile depends on brake and load target. |
This REX-08 setup was built for an M6 owner who wanted a stronger, lighter, and more EV-specific wheel package. The 18-inch diameter keeps tire sidewall practical, while the ET42 square specification gives the M6 a clean stance without spacer dependency.
The primary row comes from an LFI customer fitment record. Alternate rows are reference directions only, then LFI still checks brake template, tire shoulder, load target, and the actual ride height before production.
| Direction | Wheel size | Wheel model | Best for | Notes |
|---|---|---|---|---|
| Primary | 18x8 ET42 | REX-08 | Real LFI build record | LFI customer fitment record. Confirm tire shoulder, brake template, ride height, and final offset. |
| Alternate | Same diameter, +0.5 in width, offset within 5 mm | LFI CSF1 V3 Racing Forged Wheel | More visual aggression | Reference benchmark. Verify tire shoulder, brake template, ride height, and fender clearance before production. |
| Additional | One inch larger diameter with conservative width | LFI CSF3 V2 Racing Forged Wheel | Show-oriented street fitment | Reference benchmark. Confirm tire diameter, load rating, brake clearance, and road-use comfort first. |
Wheel fitment is more than diameter and offset. LFI reviews vertical load, braking and drive torque, spoke-root behavior, hub-pad stress, bolt-seat stress, and combined load cases before final production.
For this guide, LFI uses an aggressive EV MPV rear-axle working baseline of 1600 kg, or 800 kg per wheel. The preferred customer-facing target in this table is 950 kg per wheel when the wheel family allows it.
Wheel strength is not only vertical load. LFI also reviews acceleration, braking, cornering, potholes, tire grip, hub-pad stress, bolt-seat stress, spoke-root stress, and rim-barrel torque reaction against an approximately 2,000 Nm per wheel static torque load target.
If you want the manufacturing side of the process, LFI's How LFI Wheels Are Made page shows the design, forging, CNC machining, finishing, and QC logic behind a custom forged wheel before it ever reaches the car.
| Wheel load rating | Per-axle equivalent | Margin vs axle baseline | Status | How LFI positions it |
|---|---|---|---|---|
| 790 kg | 1580 kg per axle | -1% vs 800 kg/wheel | Low reserve | Use only after exact axle data, tire load, and duty cycle are confirmed. |
| 890 kg | 1780 kg per axle | +11% vs 800 kg/wheel | Preferred | Road-use, fast-road, and daily forged applications with useful axle-load reserve. |
| 950 kg | 1900 kg per axle | +19% vs 800 kg/wheel | Preferred | Road-use, fast-road, and daily forged applications with useful axle-load reserve. |
| 1050 kg | 2100 kg per axle | +31% vs 800 kg/wheel | Extra reserve | Extra reserve for passengers, luggage, harsher roads, heavy tires, and frequent full-load use. |
| Validation load case | Reference basis | Suggested LFI target | Why it matters |
|---|---|---|---|
| Radial vehicle load | Vehicle mass, passengers, tire package, and selected wheel load target | 950 kg preferred target | Represents vehicle mass and repeated road loading. |
| Torque load | Conservative 1g dry braking check with 60% front bias | ~2,000 Nm per wheel | Loads the hub pad, bolt seats, spoke roots, and rim barrel. |
| Cornering load | Lateral force from road grip, sticky tires, and fast-road or track use | Application-specific | Shows how the wheel behaves when the chassis loads sideways during aggressive cornering. |
| Combined static load case | Radial load + torque load + cornering load | Application-specific | More realistic than isolated vertical checks because real driving loads rarely occur one at a time. |
Engineering Article
For forged wheel applications, vertical load is only one part of the engineering picture. LFI also reviews spoke-root stress, hub-pad loading, bolt-seat behavior, rim-barrel stress, and combined static road-load cases where relevant.
| Term | Meaning | How it applies to LFI custom wheels |
|---|---|---|
| JWL | Japanese technical standard for light alloy wheels. | Used as a reference standard for relevant load and durability requirements. |
| VIA | Japanese third-party wheel registration and verification system. | Applies only to specific wheel models/specifications that are formally registered. |
| TUV | European technical testing or certification framework. | Applies only when a specific wheel/specification has supporting TUV documentation. |
| SAE | Common industry test framework for aftermarket wheel performance and impact evaluation. | Useful for impact and fatigue validation depending on market and specification. |
| Internal validation | LFI's own engineering and test process. | Used for bespoke specifications built from validated design families. |
| Static FEA | Computer-based engineering simulation. | Used before machining to evaluate stress, weight, torque load, and clearance. |
Selected high-volume reference specifications may be supported by external lab reporting or third-party documentation. Bespoke BYD M6 specifications are engineered from the same design families and reviewed through LFI's internal design, load, brake-clearance, and fitment-validation process. See LFI's Testing & Compliance for published standards and test references.
This REX-08 setup was built for an M6 owner who wanted a stronger, lighter, and more EV-specific wheel package. The 18-inch diameter keeps tire sidewall practical, while the ET42 square specification gives the M6 a clean stance without spacer dependency.
These wheel models are selected around the vehicle type instead of a generic forged-wheel fallback.
EV-focused design for heavier platforms and range-conscious fitment planning.
Clean EV performance styling for daily electric crossovers and sedans.
Lightweight forged response with broad brake-clearance flexibility.
LFI supports BYD M6 customers with vehicle-specific forged wheel consultation, DDP supply where available, and direct Singapore / Malaysia support. Fitment recommendations are based on the confirmed vehicle, brake package, tyre target, load requirement, and intended use.
LFI helps owners choose between OEM+, lightweight square, brake-clearance, show-style, and track-focused forged setups.
City roads, highways, potholes, wet-weather tires, ride comfort, and tire availability can all change the best wheel and tire recommendation.
LFI offers Duty Paid Shipping (DDP) to major markets, so eligible customers pay the confirmed landed price with no extra import tariffs or taxes due on delivery.
Singapore customers can visit LFI at 76 Playfair Road, #01-03, Singapore 367996 to view forged wheel samples, finishes, concavity profiles, and selected in-stock wheels.
Malaysia customers can order directly with LFI and request pre-production consultation for road use, track use, tire availability, and brake clearance.
| Reference | What it supports | Link |
|---|---|---|
| Owner Manual / VIN Data | Factory tire, wheel, tire-pressure, and axle-label information for the exact vehicle. | Owner Manual / VIN Data |
| JWL / VIA Wheel Standards | Japanese light-alloy wheel standard and third-party verification context for JWL / JWL-T marking and VIA registration. | Japan Light Alloy Automotive Wheel Testing Council |
| TUV SUD Wheel Testing | Independent laboratory testing context for wheels, materials, components, fatigue testing, impact testing, and international wheel standards. | TUV SUD Wheel Testing |
| Standards Testing Laboratories | Automotive wheel test-lab context for fatigue, impact, load / deflection, and compliance-related validation. | STL Testing Services |
| SAE J2530 | Aftermarket passenger-car and light-truck wheel performance requirements and test-method context. | SAE J2530 |
Yes. The case studies are based on real LFI forged-wheel customer projects and fitment records.
Recorded LFI references point to 5x120 PCD. LFI confirms the exact vehicle before machining.
Recorded hub-bore references show 64.1. LFI confirms the hub-centric machining value against the actual car before quoting or production.
A recorded starting point is 18x8 ET42. Tyre pairing, brake clearance and ride height are confirmed around the actual car.
Yes, when the offset, brake clearance, and body clearance are engineered into the forged wheel specification.
Some recorded builds have full specification value while customer images are still pending.
Send the model year, trim, brake package, tyre target, ride height, alignment notes, PCD, hub bore, hardware seat, centre-cap plan, finish, load target and intended use.
Yes. LFI supports local Singapore and Malaysia customers and ships forged wheels internationally with fitment consultation.
Yes. The photos are fitment references. LFI can quote gloss, satin, brushed, polished, bronze, black, silver, and custom finishes depending on the wheel design.
No. The photographed setup is a proven reference point, but LFI can adjust width, offset, concavity, finish, and tire pairing around your car and goals.
Brake clearance depends on the caliper template, barrel profile, spoke shape, backpad, and final offset. LFI checks these before machining.
Yes. A comfort-biased setup can use a more conservative width, sensible offset, and tire sizing with enough sidewall for road use.
Yes, but fender clearance, steering clearance, tire shoulder, ride height, and alignment need to be checked together.
Often yes, if the cap diameter, clip style, pocket depth, and face profile are planned before production.
Yes. Square setups are popular when owners want easy tire rotation, predictable handling, and a clean road-use package.
Yes. Staggered setups can work when the platform, tire diameter, and drivetrain requirements support it.
Two tires with the same printed size can sit differently. Shoulder shape affects fender clearance, steering clearance, and the final stance.
Offset only tells part of the story. Width, tire size, brake clearance, hub geometry, concavity, and ride height all affect whether the setup works.
Yes. LFI supports international forged-wheel orders and can prepare fitment consultation remotely before production.
Share your model year, brake package, tire target, ride height, alignment, center-cap plan, and finish target so LFI can confirm the forged wheel specification.